New BLYNK IOT Automation

 //https://blynk.cloud/dashboard/61173/global/filter/352881/organization/61173/devices/180825/dashboard

// Fill-in information from your Blynk Template here

#define BLYNK_TEMPLATE_ID "xxxxxxxxxx"// Enter the Blynk template ID here

#define BLYNK_DEVICE_NAME "Anokhautomation"// Enter the Blynk Device Name here

//#define BLYNK_DEVICE_NAME ""

#define BLYNK_FIRMWARE_VERSION        "0.1.0"

#define BLYNK_PRINT Serial

#define BLYNK_DEBUG

//#define APP_DEBUG

// Uncomment your board, or configure a custom board in Settings.h

//#define USE_SPARKFUN_BLYNK_BOARD

#define USE_NODE_MCU_BOARD

//#define USE_WITTY_CLOUD_BOARD

// define the GPIO connected with Relays

#define RelayPin1 5  //connect Relay 1 to D1 pin of Node MCU

#define RelayPin2 4  //connect Relay 2 to D2 pin of Node MCU

#define RelayPin3 14 //connect Relay 3 to D5 pin of Node MCU

#define RelayPin4 12 //connect Relay 4 to D6 pin of Node MCU

// define the GPIO connected with push buttons

#define SwitchPin1 2  //connect push button 1 to D4 pin of NodeMCU

#define SwitchPin2 D3 //connect push button 2 to D3 pin of NodeMCU

#define SwitchPin3 13 //connect push button 3 to 7 pin of NodeMCU

#define SwitchPin4 3  //connect push button 4 to RX pin of NodeMCU

#define wifiLed   16   //CONNECT AN LED TO D0 PIN OF NODE MCU TO INDICATE NETWORK STATUS.

//Change the virtual pins according the rooms

#define VPIN_BUTTON_1    V1

#define VPIN_BUTTON_2    V2

#define VPIN_BUTTON_3    V3 

#define VPIN_BUTTON_4    V4

// Relay State

bool toggleState_1 = LOW; //Define integer to remember the toggle state for relay 1

bool toggleState_2 = LOW; //Define integer to remember the toggle state for relay 2

bool toggleState_3 = LOW; //Define integer to remember the toggle state for relay 3

bool toggleState_4 = LOW; //Define integer to remember the toggle state for relay 4

#include "BlynkEdgent.h"

BLYNK_CONNECTED() {

  // Request the latest state from the server

  Blynk.syncVirtual(VPIN_BUTTON_1);

  Blynk.syncVirtual(VPIN_BUTTON_2);

  Blynk.syncVirtual(VPIN_BUTTON_3);

  Blynk.syncVirtual(VPIN_BUTTON_4);

}

// When App button is pushed - switch the state

BLYNK_WRITE(VPIN_BUTTON_1) {

  toggleState_1 = param.asInt();

  if(toggleState_1 == 1){

    digitalWrite(RelayPin1, LOW);

  }

  else { 

    digitalWrite(RelayPin1, HIGH);

  }

}

BLYNK_WRITE(VPIN_BUTTON_2) {

  toggleState_2 = param.asInt();

  if(toggleState_2 == 1){

    digitalWrite(RelayPin2, LOW);

  }

  else { 

    digitalWrite(RelayPin2, HIGH);

  }

}

BLYNK_WRITE(VPIN_BUTTON_3) {

  toggleState_3 = param.asInt();

  if(toggleState_3 == 1){

    digitalWrite(RelayPin3, LOW);

  }

  else { 

    digitalWrite(RelayPin3, HIGH);

  }

}

BLYNK_WRITE(VPIN_BUTTON_4) {

  toggleState_4 = param.asInt();

  if(toggleState_4 == 1){

    digitalWrite(RelayPin4, LOW);

  }

  else { 

    digitalWrite(RelayPin4, HIGH);

  }

}

void setup()

{

  Serial.begin(115200);

  delay(100);

  

  pinMode(RelayPin1, OUTPUT);

  pinMode(RelayPin2, OUTPUT);

  pinMode(RelayPin3, OUTPUT);

  pinMode(RelayPin4, OUTPUT);

  pinMode(wifiLed, OUTPUT);

  pinMode(SwitchPin1, INPUT_PULLUP);

  pinMode(SwitchPin2, INPUT_PULLUP);

  pinMode(SwitchPin3, INPUT_PULLUP);

  pinMode(SwitchPin4, INPUT_PULLUP);

  //During Starting all Relays should TURN OFF

  digitalWrite(RelayPin1, HIGH);

  digitalWrite(RelayPin2, HIGH);

  digitalWrite(RelayPin3, HIGH);

  digitalWrite(RelayPin4, HIGH);

  digitalWrite(wifiLed, HIGH);

  BlynkEdgent.begin();

  Blynk.virtualWrite(VPIN_BUTTON_1, toggleState_1);

  Blynk.virtualWrite(VPIN_BUTTON_2, toggleState_2);

  Blynk.virtualWrite(VPIN_BUTTON_3, toggleState_3);

  Blynk.virtualWrite(VPIN_BUTTON_4, toggleState_4);

}

void loop() {

    BlynkEdgent.run();

    

    manual_control(); //Manual Switch Control   

}